Below is a brief overview of this Project Work.
Format: MS WORD
| Chapters: 1-5
| Pages: 82
ENHANCED OIL RECOVERY IN HIGH VISCOUS RESERVOIR USING THE THERMAL PROCESS
ABSTRACT
New sources of energy should be found to relieve the high demand of energy. Even though heavy oil and bitumen are difficult to produce due to their high viscosity which can be reduced by heating, with increased oil price, the production of these heavy oils are seen viable thus the need for a model that would help make predictions for the future and also take into consideration areal and vertical sweep of hydrocarbons (3D simulator). The ability to be able to optimize the interaction data and decision making during the life cycle of the field is critical. As a result of a heterogeneity of reservoirs, numerical simulators are used to obtain consistent and significant solutions. For this work, a three-dimensional numerical reservoir simulator is developed for an expansion drive with a high viscous oil. A transient state heat system by conduction with an internal heat source is considered. A temperature simulator is first developed then coupled with a viscosity correlation after which it is then coupled with a diffusivity equation for a single phase flow of an expansion drive reservoir. All the governing equations are discretized using finite difference technique; iterative linear solver with the aid of MATLAB code is used to solve the system of linear equations. This work aims to look at the effect of temperature on pressure drop through viscosity. It is realized that an increase in the heat source introduced a rise in temperature which in turn decrease the viscosity across the system. The pressure across the system is seen to be sustained even though it is declining thus the pressure being maintained.
CHAPTER ONE
INTRODUCTION
1.1 General Introduction
Reservoirs act differently due to varying range of both rock and fluid properties and thus must be treated uniquely. During production, reservoirs are allowed to naturally produce their hydrocarbons until when production rates are mostly not economical viable then other support systems are used. Primary recovery is the natural stage of the reservoir to be able to produce without support thus depending on reservoir’s internal energy. There are different drive mechanisms known as a results of different energy sources. The drive mechanism of a reservoir is not known in the earlier life of the production but can be seen from production data with time. The knowledge about the reservoir’s drive mechanism can help improve reserves recovery and supervision during its middle and later life. The important drive mechanisms include: Rock and liquid expansion drive, solution gas/ depletion drive, Gas cap drive, Water drive, Combination drive and Gravity drainage drive.
Rock and liquid expansion drive has its oil existing at a higher pressure than the bubble point pressure and with only oil, connate water and the rocks. The rock and fluids expand as a result of their different compressibility as the reservoir pressure deplete. Formation compaction and expansion of different rock grains are some factors that affect reservoir rock compressibility. These factors are due to decrease of fluid pressure within the pore spaces which in turn reduce pore volume through porosity reduction. While the pore volume is reducing, the crude oil and water will be forced out of the pore space to the wellbore. Due to the compressibility (slightly) of both liquids and rocks, the reservoir will experience a rapid pressure decline. A constant gas-oil ratio equal to gas solubility at bubble point pressure is typical of this drive mechanism. A small percentage of total oil in place is recovered due to the less efficiency of this drive.
Other recovery methods like Secondary and tertiary (Enhanced) recovery methods are employed to help improve the recovery of the remaining hydrocarbons by providing additional or sustaining the energy. The efficiency of an enhanced recovery method is a measure of its ability to provide greater hydrocarbon recovery than by natural depletion at economically attractive production rate (Marcel et al. 1980). It depends on reservoir characteristics and nature of displacing and displaced fluids. Enhanced recovery methods seeks to improve the sweep and displacement efficiency. It has been basically grouped into three types; namely chemical processes, miscible displacement processes and thermal processes.
ABSTRACT
New sources of energy should be found to relieve the high demand of energy. Even though heavy oil and bitumen are difficult to produce due to their high viscosity which can be reduced by heating, with increased oil price, the production of these heavy oils are seen viable thus the need for a model that would help make predictions for the future and also take into consideration areal and vertical sweep of hydrocarbons (3D simulator). The ability to be able to optimize the interaction data and decision making during the life cycle of the field is critical. As a result of a heterogeneity of reservoirs, numerical simulators are used to obtain consistent and significant solutions. For this work, a three-dimensional numerical reservoir simulator is developed for an expansion drive with a high viscous oil. A transient state heat system by conduction with an internal heat source is considered. A temperature simulator is first developed then coupled with a viscosity correlation after which it is then coupled with a diffusivity equation for a single phase flow of an expansion drive reservoir. All the governing equations are discretized using finite difference technique; iterative linear solver with the aid of MATLAB code is used to solve the system of linear equations. This work aims to look at the effect of temperature on pressure drop through viscosity. It is realized that an increase in the heat source introduced a rise in temperature which in turn decrease the viscosity across the system. The pressure across the system is seen to be sustained even though it is declining thus the pressure being maintained.
CHAPTER ONE
INTRODUCTION
1.1 General Introduction
Reservoirs act differently due to varying range of both rock and fluid properties and thus must be treated uniquely. During production, reservoirs are allowed to naturally produce their hydrocarbons until when production rates are mostly not economical viable then other support systems are used. Primary recovery is the natural stage of the reservoir to be able to produce without support thus depending on reservoir’s internal energy. There are different drive mechanisms known as a results of different energy sources. The drive mechanism of a reservoir is not known in the earlier life of the production but can be seen from production data with time. The knowledge about the reservoir’s drive mechanism can help improve reserves recovery and supervision during its middle and later life. The important drive mechanisms include: Rock and liquid expansion drive, solution gas/ depletion drive, Gas cap drive, Water drive, Combination drive and Gravity drainage drive.
Rock and liquid expansion drive has its oil existing at a higher pressure than the bubble point pressure and with only oil, connate water and the rocks. The rock and fluids expand as a result of their different compressibility as the reservoir pressure deplete. Formation compaction and expansion of different rock grains are some factors that affect reservoir rock compressibility. These factors are due to decrease of fluid pressure within the pore spaces which in turn reduce pore volume through porosity reduction. While the pore volume is reducing, the crude oil and water will be forced out of the pore space to the wellbore. Due to the compressibility (slightly) of both liquids and rocks, the reservoir will experience a rapid pressure decline. A constant gas-oil ratio equal to gas solubility at bubble point pressure is typical of this drive mechanism. A small percentage of total oil in place is recovered due to the less efficiency of this drive.
Other recovery methods like Secondary and tertiary (Enhanced) recovery methods are employed to help improve the recovery of the remaining hydrocarbons by providing additional or sustaining the energy. The efficiency of an enhanced recovery method is a measure of its ability to provide greater hydrocarbon recovery than by natural depletion at economically attractive production rate (Marcel et al. 1980). It depends on reservoir characteristics and nature of displacing and displaced fluids. Enhanced recovery methods seeks to improve the sweep and displacement efficiency. It has been basically grouped into three types; namely chemical processes, miscible displacement processes and thermal processes.
How to Download the Full Project Work for FREE
- You can download the Full Project Work for FREE by Clicking Here.
- On the other hand, you can make a payment of ₦5,000 and we will send the Full Project Work directly to your email address or to your Whatsapp. Clicking Here to Make Payment.