Below is a brief overview of this Project Work.
Format: MS WORD
| Chapters: 1-4
| Pages: 51
DESIGN AND CONSTRUCTION OF BATTERY CHARGER
ABSTRACT
This project which consists of four chapters deals extensively with the design and construction of a battery charger which is capable charging a 12 volts, battery. The first chapter which is the introductory chapter goes a long way in defining the battery charger and explaining of the mode of operation. The second chapter went further to explain each component part of the battery charger. This ranges from:
1. The transformer
2. The rectifier circuit
3. The filtering stage
4. Voltage regulation
5. Comparator
6. Thyristor
7. Resistor
8. Diode
9. Relay
10. Zener diode and
11. Light emitting diode (LED)
The third chapter explains more about the Testing Sensing and switching processes in the charger. It also gave the list of components and the circuit diagram of the battery charger. The concluding chapter being fourth, tells us more about the circuit arrangements and the construction of casing and finally the overall cost analysis.
CHAPTER ONE
1.1 INTRODUCTION
A device, which consist of electrodes and electrolyte for the storage of chemical energy, but brings about a reaction between its electrodes and the electrolyte in a way to cause the flow of electrons through an external circuit is known as a battery. There are two types of batteries, these include the primary and secondary battery. The primary (dry cell) is one whose electrolyte dries up when used to its ampere-hour rating and cannot be recharged while the secondary (wet cell) is one whose chemical energy can be restored through a charging process. There are different types of secondary battery. These comprises lead acid, Nickel-cadmium and silver zinc battery.
Furthermore, a battery is a combination of cells connected together and a cell is a simple source of electric potential. The maintenance of secondary battery is of importance partially where maximum performance and life are obtained. As long as a battery is in use, its stored chemical energy, which is being converted to electrical energy falls. This falls in chemical energy leads to a corresponding fall in its terminal voltage.
A constant potential method of charging is adopted in this project work. It is a phenomenon whereby the alternating voltage from the main is converted to direct voltage through rectification. The direct current from the rectifier is then passed through the battery that is being charged in the reversed direction in which the battery supplies current to the external circuit. The charger is intended to charge batteries with terminal voltage up to 12volts. It incorporates a sensing technique to monitor when the battery has been charged to its rated terminal voltage so as to automatically cut off supply to the battery.
Hence, a battery charger which is of low cost, highly efficient and cheap to maintain is needed to restore its rated terminal voltage. The entire circuit is made up of five basic units and details of each units is highlighted in the subsequent chapters.
ABSTRACT
This project which consists of four chapters deals extensively with the design and construction of a battery charger which is capable charging a 12 volts, battery. The first chapter which is the introductory chapter goes a long way in defining the battery charger and explaining of the mode of operation. The second chapter went further to explain each component part of the battery charger. This ranges from:
1. The transformer
2. The rectifier circuit
3. The filtering stage
4. Voltage regulation
5. Comparator
6. Thyristor
7. Resistor
8. Diode
9. Relay
10. Zener diode and
11. Light emitting diode (LED)
The third chapter explains more about the Testing Sensing and switching processes in the charger. It also gave the list of components and the circuit diagram of the battery charger. The concluding chapter being fourth, tells us more about the circuit arrangements and the construction of casing and finally the overall cost analysis.
CHAPTER ONE
1.1 INTRODUCTION
A device, which consist of electrodes and electrolyte for the storage of chemical energy, but brings about a reaction between its electrodes and the electrolyte in a way to cause the flow of electrons through an external circuit is known as a battery. There are two types of batteries, these include the primary and secondary battery. The primary (dry cell) is one whose electrolyte dries up when used to its ampere-hour rating and cannot be recharged while the secondary (wet cell) is one whose chemical energy can be restored through a charging process. There are different types of secondary battery. These comprises lead acid, Nickel-cadmium and silver zinc battery.
Furthermore, a battery is a combination of cells connected together and a cell is a simple source of electric potential. The maintenance of secondary battery is of importance partially where maximum performance and life are obtained. As long as a battery is in use, its stored chemical energy, which is being converted to electrical energy falls. This falls in chemical energy leads to a corresponding fall in its terminal voltage.
A constant potential method of charging is adopted in this project work. It is a phenomenon whereby the alternating voltage from the main is converted to direct voltage through rectification. The direct current from the rectifier is then passed through the battery that is being charged in the reversed direction in which the battery supplies current to the external circuit. The charger is intended to charge batteries with terminal voltage up to 12volts. It incorporates a sensing technique to monitor when the battery has been charged to its rated terminal voltage so as to automatically cut off supply to the battery.
Hence, a battery charger which is of low cost, highly efficient and cheap to maintain is needed to restore its rated terminal voltage. The entire circuit is made up of five basic units and details of each units is highlighted in the subsequent chapters.
How to Download the Full Project Work for FREE
- You can download the Full Project Work for FREE by Clicking Here.
- On the other hand, you can make a payment of ₦5,000 and we will send the Full Project Work directly to your email address or to your Whatsapp. Clicking Here to Make Payment.