This project work titled CONSTRUCTION OF A STANDARD WHEEL BARROW has been deemed suitable for Final Year Students/Undergradutes in the Chemical Engineering Department. However, if you believe that this project work will be helpful to you (irrespective of your department or discipline), then go ahead and get it (Scroll down to the end of this article for an instruction on how to get this project work).
Below is a brief overview of this Project Work.
Format: MS WORD
| Chapters: 1-5
| Pages: 33
ABSTRACT
The project is about construction of wheel barrow which is fabricated in mechanical Engineering workshop in institute of management and technology, Enugu. The report comprise five chapters, chapter one is about the introduction (background of the study) of the wheel-barrow, chapter tow is about the literature review, chapter three is about the theory and analysis of problem, chapter four is about Assembling of the wheel barrow, chapter five is about conclusion, recommendation and references.
CHAPTER ONE
INTRODUCTION
1.1 Background to the Study
It is often said that man are born free back are always in Chain, in one way or the other, human beings are faced with a lot of problem. there was a time when it is difficult to carry a load from one place to anthem but as time goes one, solutions where prefer to this problem by providing a simple machine called wheelbarrow to help transport goods form one place to another. A wheelbarrow is a small hand propelled vehicle usually with just one wheel, designed to be pushed and guided by a single person using two handles to the rear or by a sail to push the ancient wheelbarrow by wind. The machine has two hands where efforts are applied, it also has a portion where loads are loaded. The fulcrum takes change of it movement and so many other features. This machine is fabricated to relieve the difficulties and probably eliminate loss of man-power time, money and especially the need for technological break through self reliance.
1.2 AIM OBJECTIVES
The aim of fabricating this wheel barrow is as follows
1. To know how to fabricate a slandered wheel barrow.
2. To eradicate the problems faced by human’s in carrying goods form one place to another.
3. To lessen difficulties and probably eliminate lost of man-power
4. To identify how wheel barrow can be assistance in the society.
1.3 SCOPE AND LIMITATION
SCOPE
This study/work is designed to cover the construction or fabrication of a standard wheelbarrow.
LIMITATION
It is a difficult task to cover the fabrication of all simple machinery is Nigeria. The producer concentrated in the fabrication of wheelbarrow. During the fabrication, the producer also faced the following constantans.
a. Time: The time ell acted to this work is short compared to the production of the wheelbarrow.
b. Financial constraint: Financial is another problem faced by the producer during the constriction. There is no enough fund for the producer.
The project is about construction of wheel barrow which is fabricated in mechanical Engineering workshop in institute of management and technology, Enugu. The report comprise five chapters, chapter one is about the introduction (background of the study) of the wheel-barrow, chapter tow is about the literature review, chapter three is about the theory and analysis of problem, chapter four is about Assembling of the wheel barrow, chapter five is about conclusion, recommendation and references.
CHAPTER ONE
INTRODUCTION
1.1 Background to the Study
It is often said that man are born free back are always in Chain, in one way or the other, human beings are faced with a lot of problem. there was a time when it is difficult to carry a load from one place to anthem but as time goes one, solutions where prefer to this problem by providing a simple machine called wheelbarrow to help transport goods form one place to another. A wheelbarrow is a small hand propelled vehicle usually with just one wheel, designed to be pushed and guided by a single person using two handles to the rear or by a sail to push the ancient wheelbarrow by wind. The machine has two hands where efforts are applied, it also has a portion where loads are loaded. The fulcrum takes change of it movement and so many other features. This machine is fabricated to relieve the difficulties and probably eliminate loss of man-power time, money and especially the need for technological break through self reliance.
1.2 AIM OBJECTIVES
The aim of fabricating this wheel barrow is as follows
1. To know how to fabricate a slandered wheel barrow.
2. To eradicate the problems faced by human’s in carrying goods form one place to another.
3. To lessen difficulties and probably eliminate lost of man-power
4. To identify how wheel barrow can be assistance in the society.
1.3 SCOPE AND LIMITATION
SCOPE
This study/work is designed to cover the construction or fabrication of a standard wheelbarrow.
LIMITATION
It is a difficult task to cover the fabrication of all simple machinery is Nigeria. The producer concentrated in the fabrication of wheelbarrow. During the fabrication, the producer also faced the following constantans.
a. Time: The time ell acted to this work is short compared to the production of the wheelbarrow.
b. Financial constraint: Financial is another problem faced by the producer during the constriction. There is no enough fund for the producer.
How to Download the Full Project Work for FREE
- You can download the Full Project Work for FREE by Clicking Here.
- On the other hand, you can make a payment of ₦5,000 and we will send the Full Project Work directly to your email address or to your Whatsapp. Clicking Here to Make Payment.